Menu

DATASHEET OF HT12E PDF

0 Comment

The content and copyrights of the attached material are the property of its owner. Distributed by: ✦ HT12E series of Encoders Features. Operating voltage – V~5V for the – V~12V for the HT12E Low power and high noise immunity CMOS Minimum. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC.

Author: Akinos Nikorg
Country: Jordan
Language: English (Spanish)
Genre: Photos
Published (Last): 24 January 2009
Pages: 150
PDF File Size: 12.64 Mb
ePub File Size: 18.8 Mb
ISBN: 199-1-29744-452-5
Downloads: 36809
Price: Free* [*Free Regsitration Required]
Uploader: Samurr

Basically found in applications of remote control systems.

HT12E-SMD Datasheet

These are the 8-bit address bits, which is used to protect your data. As soon as TE returns to high, the encoder output completes its final cycle and then stops. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. Used for interfacing RF circuits generally MegaHz.

In additional to itit also has 8 address lines which can generally be grounded along with the pin number 9. Simply put, HT12E converts the parallel inputs into serial output.

HT12E Encoder IC

We should set the bits in same pattern on Encoder and Decoder IC to pair them. They are paired with 2 12 series of decoders for use in remote control system applications. This pin outputs the parallel data serially.

Supply voltage; 5V 2. An LED can also be connected across this terminal to indicate output. SPI Module of Arduino.

  EL DESCONTENTO Y LA PROMESA PEDRO HENRQUEZ UREA PDF

Now first of all let me acquaint you about these two integrated circuits: To find out more, including how to control cookies, see here: If you want security you can connect any of the 8 pins to 5V to make it high. This oscillator can be used by connecting these two pins through a 1M Resistor.

This IC has a total of 18 pinsnine on either sides: It is mainly used in interfacing RF and infrared circuits. This high-density System-in-Package SiP integrates datashedt, power switches, and support components. Thus this helps in setting up oscillations satasheet the IC. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Transmission enable; active low. It is very important that your Decoder should also have this same address for them to talk to each other. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.

HT12E has a transmission enable pin which datasbeet active low. You can know to set up the HT12D after this from here. Whenever an active low signal is applied at its TE pin then only the parallel data gets transferred serially at the output, otherwise the IC is in high impedance state. This pin has to be connected to Ground 0V to enable the Transmission. The IC is has a wide range of operating voltage from 2.

  JEFFREY EUGENIDES VIRGIN SUICIDES PDF

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

I am now going to tell you about to control a certain robot wirelessly rather than using wires. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, adtasheet we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. These 12 bits are divided into 8 address bits and 4 data bits.

This cycle is repeated as long as TE is kept low. They can also datxsheet connected to switches to manually send and receive data. The IC has a built in datassheet. TL — Programmable Reference Voltage.

Interface GPS with Arduino. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. Gone are the days when we used to use wires to connect two devices to establish a communication path. What is Web Browser. HT12E is an encoder integrated vatasheet of 2 12 series of encoders.

Arduino based GPS receiver.